DIY Fiberglass Hatch Covers

1

fiberglass

To protect the fixed and soft-vinyl windows aboard our PDQ 32 test boat, we have a combination of snap-on canvas covers and awnings, along with the two Outland Hatch Covers were testing. After the success we had using the Outland Hatch Covers PVC covers, we wanted to install more of them, but the cruising kitty could not bear the cost, so we sought a do-it-yourself solution.

A dock neighbor made a set from inexpensive fiberglass shower-surround material; his hatches exterior handles secured the covers. However, our test boats hatches have interior handles so we opted to use the Velcro-like Scotch Clear Extreme (3M Dual Lock) re-closeable fasteners for our DIY fiberglass covers. Heres a look at our DIY project.

Materials: 4 ft. x 8 ft. x .09 inch fiberglass wall board (Home Depot, #MFTF12IXA480009600, $33); Scotch Clear Extreme fastener ($30 for 10 feet of 1 inch wide)

Tools: Hole saws, 1 1/8 inch and 1 inch; disc sander; table saw; 150-grit sand paper

fiberglass

The Process

The first order of business was to create templates from the existing hatch windows; we did this using freezer paper, confirming measurements carefully. We transferred the template onto the fiberglass wall board by cutting out the template and tracing it using a Sharpie. Then we cut out the covers.

Careful measurement is the key. The fiberglass is easily cut to size by scoring and snapping with a plastic cutter. To allow space for sanding smooth edges, we cut the pieces 1/8-inch larger than they needed to be, then trimmed them with a disk sander (with 150-grit paper) and finished them by hand sanding.

The 1-inch circles (buttons) and the holes for the adhesive buttons (1 inch diameter) and support brackets (varies) were cut using a hole saw; we removed the center bit to cut the circles.

To install, we covered circles entirely with Dual Lock, trimming to fit. The 1 1/8-inch circle of Dual Lock that is placed on the lens was carefully trimmed to fit the 1 1/8-inch cover hole. We then snapped the Dual Lock circles onto the center of the covered buttons (backing still in place), placed the covers on the windows, and then removed the backing and applied the buttons to the holes.

We used two buttons for the smaller hatches. For larger hatches, four buttons located in the corners worked well. If the hatch has external handles, you can replace two of the buttons with holes drilled to slide over these handles; the fiberglass will flex.

Conclusions

The DIY covers have stayed in place underway and through a few squalls, but we remove them for offshore work. The buttons are the most vulnerable part-they can be removed with a swift kick from a careless foot-so we made extras. In six months, we havent lost any buttons or covers.

The total cost was about $64, which comes to $5 per 21-by-21-inch hatch cover, allowing for waste and assuming you will use all of the material eventually. If youre making several covers, going the DIY route is a money-saver over the Outland Hatch Covers. Also, if your hatches are oddly shaped or sized-and youre handy-the DIY solution is worth considering.

While we are pleased with our DIY fiberglass covers, we still prefer our snap-on Sunbrella covers for fixed windows and vinyl skylights-they are fast, secure, and compact to store. The Outland Hatch Covers are ideal for high-traffic areas, like around the mast.

Darrell Nicholson
Practical Sailor has been independently testing and reporting on sailboats and sailing gear for more than 50 years. Its independent tests are carried out by experienced sailors and marine industry professionals dedicated to providing objective evaluation and reporting about boats, gear, and the skills required to cross oceans. Practical Sailor is edited by Darrell Nicholson, a long-time liveaboard sailor and trans-Pacific cruiser who has been director of Belvoir Media Group's marine division since 2005. He holds a U.S. Coast Guard 100-ton Master license, has logged tens of thousands of miles in three oceans, and has skippered everything from pilot boats to day charter cats. His weekly blog Inside Practical Sailor offers an inside look at current research and gear tests at Practical Sailor, while his award-winning column,"Rhumb Lines," tracks boating trends and reflects upon the sailing life. He sails a Sparkman & Stephens-designed Yankee 30 out of St. Petersburg, Florida. You can reach him at darrellnicholson.com.

1 COMMENT